Freeing the CLP-315 without modchip

Samsung’s CLP-315 (and CLP-310) are the smallest and cheapest laser color printers around. They just suffer one problem: Samsung protected it against generic toners and its expensive original consumables totally counter-balance the hardware low price. As each page is counted in both toner and printer, refills are also not possible. Printing 1000 white pages will require a new toner: unacceptable and definitively not a ‘green’ product (see Planned Obsolescence). Modifying your printer will allow you to extend your consumables life, or, if you want to risk your health and printer hardware, refill them.

Current chip market

Many chips can be found, with or without refill kits, on ebay. Prices range from $20 to 49$.

Seems Samsung changed the gameplay by updating and reinforcing the mainboards, as some chips states working only on units prior to July 2009. Some claim disabling the CLP-315W wifi.

By looking at installation pictures, seems that they all target the same IC, using 3 to 7 wires.

5 wires chip from Turkey

Some 5 wire chip from china. Note that an IC is removed.

Another version with 7 wires from china. IC removed.

And one 3 wires chip. No IC removal.

Lots of different modchips, and lots of behaviours… but we can guess from them:

  • The IC is the key
  • Removing the IC breaks WiFi
  • Toners chips contacts needs to be taped or removed.

About the protection

The CLP-300 (previous model) was using cylindrical toner cartridges including chips. Replacement chips can be found and some people managed to directly erase/rewrite the counters on those.

The CLP-310/315 now includes an internal counter to avoid reprogrammed old toners. The printer stores counts in both toner and IC (the target of the modchips).

Some google results also states that the first toners have no chip counter (where 4×3 pins contacts from the printer toner door connects to), and those ones can’t be refilled with the 3 wire chips once they are depleted. The printer starts verifying the toners after the first 1000 pages. If there’s no need of tweaking toners on new printers, can the printer IC be reset ? I did not found much resources about this, except one spanish blog linking to a no longer available russian page and czech forum. What could be understood (less than a little), is that it seems possible to achieve bocking the counter by just unsoldering one and joining two pins of the IC.

The mainboard IC being a flash 24C64WP from ST Microelectronics. The linked pins are WC and Vcc. By looking at the datasheet, the WP pin appears being a ‘Write Protect’ function for the IC. This now makes sense ! Pages counter is blocked just by enabling the internal write protection: Driving it high by connecting it to Vcc. Let’s give it a try !

The mod

This modchipless modification is for new or less than 1000 pages units.

I auctioned a CLP-315 printer for $90. Printing the configuration shown that pages were 2 black and 0 colors pages counted.

Don’t complain this broke your printer: you’ll loose your printer warranty and this modification is at your own risk ! If you never soldered, if you don’t have the right tools and if you don’t know about static charges: don’t do it.

Disassembling procedure can be found for this model:

You should end up with an exposed mainboard. The IC chip being labeled ‘U1’.

Remember how you have extracted the right cover from the front door. This is the most difficult step is reassembly !

The chip is effectively a 24C64WP, but it is on a different location.

The mainboard could be removed, but this is a risky step as many wires are connected to it. The plugs can break easily by pulling them. If you don’t have the tool to remove them (each plug have a 0.3mm plastic handle on each side), soldering will be uncomfortable, but possible. I personally chosen to rotate the printer and face up mainboard, at the risk of loosing some toner powder.

Identify the chip (U1 on mainboard) and unsolder the pin 7 (counted counter clockwise, IC mainboard mark on left). Mine was near CMS C25. This could be quite difficult, so here’s a tip: Start removing some welding (using pump) and then create a “lasso” with some kynar wire. Pulling the lasso horizontally while heating the pin should raise it a bit. A needle will help once freed from mainboard contacts. As the grounded pin on the mainboard would create a short-circuit after being connected to Vcc, so carefully check it is not touching.

Apply some solder on the two pins and solder the wire, joining them: that’s all.

You should end up with something cleaner than this… or this would mean you shook as much as me 🙂

Check connections with a multimeter and reassemble unit.

Printing some pages and checking counter (Hold down power button for 5 seconds) showed a still increasing counter. Powering the unit it off for few seconds resets the state to the previous one. The counters are blocked !

About commercial modchips

So what are doing the modchips ? Here’s my guess:

  • The 3-Wire one is just write-protecting. This is the same as doing the previous modification.
  • The 5 wires or 7 wires chips, requiring original IC removal, are replacement ICs. They contain a copy of the counters and configuration of a new unit. Once soldered they act like a new unit write protected IC. This is why it warns that CLP315W users won’t be able to use WiFi: The mac address isn’t the device’s one and/or WiFi keys/configuration can’t be saved.
  • The 5 wires one is more interesting. As the original one has no pins unsoldered, I think this one acts as a IC partial reprogrammer when the printer is idle, and/or invalidates some addresses. This is why this kind of modchip works for any printer and still let the user to use and save his wifi configuration.

Then do you need a chip ?

  • If you printer is new or under 1000 pages: No. Just write protect the flash.
  • If you reached 1000 pages: You’ll need one as you printer will require query toner chips. Another solution would be to rewrite the IC and tape toners chips contacts: this need to be confirmed.

Note that if your counters are showing 997 pages, Write protecting will only allow you to print 3 pages before you’ll need to power cycle printer.

Here’s a diagram of the page count check process: (based on my assumptions)